1. 10R-7671 Injection Basic Information

2. 10R-7671 Injection Common Part Number

 (1)  Injection Exchange Information

• 10R-7671 Matching Information

3. 10R-7671 Injection Part Number Common Writing

320-0677，320 0677，3200677，10R-7671，10R 7671，10R7671，2645 A746，2645A 746，2645 A 746，2645A746

4. 10R-7671 Injection Quality Control

• InjectionTesting

All injection spare parts are tested for electrical characteristics, accuracy, high temperature, low temperature, withstand voltage, leakage, durability, and various working conditions.

• InjectionAssembling

And the quality control of the injection production and installation process, our company strictly follows the standard product installation File and product installation steps to install, such as injection stroke test, injection solenoid valve tightening torque, injection nozzle tightening torque.

• InjectionInspection

The factory inspection of the injection is undergone full inspection, random inspection, and batch inspection three inspections. Different brands of test benches are used to test the same fuel injection for a total of no less than three times for factory inspection, and the fuel injection installation testing environment are progressed in dust-free workshop.

5. 10R-7671 Injection Customized Service

（1）Injection Customized Service: Meet the customized needs of OEM manufacturers for shell lettering, logo engraving, injection internal packaging, injection external packaging and labels customized, etc.

（2）Injection Customized Service Requirements：

The purchased of customized injection are not less than 10 pieces.

Customized injection packages no less than 1000 pieces.

Customized products involve the need of specify logo, the OEM manufacturer needs to provide trademark authorization and the sample of logo image File.

Once the customized fuel injection is sold, it cannot be returned or exchanged if there is no quality problems.

6. 10R-7671 Injection Reasons of Not Working Normally

• There is air in the oil circuit of the engine fuel system.
• Vehicle oil pump oil supply system is not normal.
• Engine common rail system oil leakage or pressure limiting valve damage.
• There is a short circuit, cutting out and poor contact in the wiring harness connected to the fuel injectionof the vehicle.
• The long-term placement of the injectioncauses the anti-rust oil to solidify, and the internal components are stuck or the oil holes are blocked.
• Before installing, carefully check whether other components in the common rail system except the fuel injectionare damaged so as to prevent the fuel injectionfrom not working properly after being replaced.

7. 10R-7671 Injection Shipping Ways

Destination in China areas: SF Express, Debon Express, the corresponding logistics company can be provided according to customer requirements in special cases.

Destinations out of China’s areas： DHL, UPS, FedEx, TNT air, ocean or other shipping methods required by customers.

8. 10R-7671 Injection Lead time

Lead time：Send out within 3 – 7 working days after receiving payment（Except for special products and special cases）.

9.10R-7671 Injection Storage Standard

• Choose a suitable storage place

The warehouse and cargo yard where the fuel injection is stored should be kept clean and dry, and away from the factory buildings that generate harmful gases and dust; do not mix with acid, alkali, salt and other substances; the storage place should have a good drainage system; the cargo yard should be flattened with gravel or furnace ash etc. to enhance the water permeability of the surface layer to keep the reservoir area dry.

• Strict requirementsof warehousing

Strict inspections should be carried out when the fuel injections are put into storage, the surface cleaning work should be done well to remove water traces, oil stains, ash and other dirt, remove the rust and do anti-rust treatment in time. Packaged injections must be protected from damage.

• Keep the warehouse dry and preventing moisture

The relative humidity is usually below 70% for the fuel injections placed in the room, and the corrosion of the fuel injections is significantly reduced.

injections must be stored in the warehouse, and they are forbidden to store in the same warehouse with commodities with high water content.

• StackProperly

After the injection is exposed to rain, the corrosion rate will increase significantly. The purpose of sealing is to isolate the injection from rainwater and humid air, so the warehouse window should be checked in time to avoid rainwater entering the warehouse

If the fuel injection package is damaged, it should be repaired or replaced; when the package is damp, the packaging material should be dried; if the original anti-corrosion and oil applied at the factory is found to be damaged or dried up, it should be cleaned and re-applied oil in time.

• It is forbidden to leave the injectionexposed in the air for a long time.
• It is forbidden to store acid, alkali, saltand other substances together with the injection.
• The unpacked fuel injectionmust be rust-proof during secondary storage.

10. 10R-7671 Injection Packing

Domestic express packaging：Usually wrapped in waterproof scotch tape, such as picture No.2.

International express packaging：Wrapped with waterproof yellow tape After wrapping the black protective film, such as picture No. 3.

Pallet Shipping：Use fumigation free and recycling trays that meet export requirements, and use white wrapping protective film to wrap and bind with cable ties for the outside, such as picture No. 4,also, the products can be packaged according to customers’ requirements.

• The packing tray is made of plastic and can be recycled.
• Transparent tape, yellow tape, black wrapping protective film, white wrapping protective film are non-degradable materials, please dispose of them properly.
• Minors are prohibited from using transparent tape, yellow tape, black wrapping protective film, and white wrapping protective film to avoid personal injury.
  • 

    Pic No. 1

    

    Pic No. 2

     

    

    Pic No. 3